The following table lists active product lines and their associated approvals. Hover over the organization name or acronym to reference the association symbol.
Click on the organization symbol to view the certificate. Not all certificates are available online.
The ATEX Directives require employers to classify where hazardous explosive atmosphere can occur and equipment used in potentially explosive environments. Mechanical and electrical equipment, as well as protective systems, must comply with the ATEX (ATmospheres EXplosibles) Directive. ATEX certification allows the CE and Ex marks. Approved models and their ATEX safety rating are listed in the EU Declaration of Compliance.
The China Compulsory Certificate (CCC) mark issued by the China Certification and Accreditation Administration (CNCA) is a compulsory safety mark for both domestically manufactured products and products imported, sold, or used in the Chinese market.
A valid CE mark affixed to a product indicates that it complies with the relevant European Union product safety directives.
The Canadian Registration Number is issued by each Canadian province or territory. It covers pressure vessels, fittings, or pressure piping. It is a necessary authorization allowing these components to be in operation in Canada.
|Canada and United States||CSA
CSA certification indicates that a product, process or service has been tested to a Canadian or U.S. standard and it meets the requirements of an applicable Canadian Standards Association (CSA) standard or another recognized document used as a basis for certification. It provides an increased assurance of quality and safety. In the U.S., CSA International is accredited by the Occupational Health and Safety Administration (OSHA). (Certificate #2074191)
|European Union||EMC (2014/30/EU)
The Electromagnetic Compatibility Directive applies to all electronic or electrical products liable to cause or be disturbed by electromagnetic interference (EMI). Compliance allows a manufacturer to use the CE marking.
|United States||Environmental Protection Agency
Kurz meets the certification requirements for: Greenhouse gas (GHG) reporting (CFR Title 40, Part 98.34 (c) and Relative accuracy and zero‐span drift check (CFR Title 40, Part 75)
|Canada and United States||
The cETLus Mark is proof that a product meets Canadian and US safety standards. ETL (Electrical Testing Labs) is a division of Intertek Testing Laboratories and is an OSHA recognized NRTL and in a similar capacity, is recognized as a Testing Organization and Certifying Body in Canada by the Standards Council of Canada.
Technical standards are maintained by the Euro‐Asian Council for Standardization, Metrology and Certification (EASC). GOST standards are regional, and GOST R standards are national.
The Hart Protocol is a global standard for bidirectional (sending and receiving) digital communication between smart devices/field instruments and control or monitoring host system (such as a technician's hand‐held device or laptop, a plant's process control, or asset management, safety or other system using any control platform).
The International Electrotechnical Commission determines the suitability of electrical equipment in flammable or explosive gas atmospheres.
(2006/95/EC) The Low Voltage Directive ensures that electrical equipment within certain voltage limits both provides a high level of protection. It covers electrical equipment with a voltage between 50 and 1000 V for alternating current and between 75 and 1500 V for direct current.
(2006/95/EC) MCERTS is the European and U.K. Environment Agency’s Monitoring Certification to ensure the quality requirements for monitoring emissions into the environment. Receiving certification for this EU Directive ensures compliance that the instrumentation is suitable for use in waste incineration and large coal-fired combustion plant applications. The CEM is proven suitable for its measuring task (parameter and composition of the flue gas) by use of the QAL 1 procedure specified in EN14181, for LCPD/IED Chapter III and IED Chapter IV applications.
NAMUR (an international association of process instrumentation user companies) recommends a standardized signal level for transmitter failure. The measurement information range is 3.8 to 20.5 mA, with measurements below and above that range indicating failure information.
The Pressure Equipment Directive defines the design, manufacture, testing, and conformity assessment of pressure equipment and assemblies of pressure equipment. A company that meets the directive can use the CE mark.
|Korean Safety Law||EK
The Korean EK mark is equivalent to the IEC standards except for the power supply (220V, 60Hz) and the type of plug.
The approval process for Continuous Emissions Monitoring Systems (CEMS) and Automated Monitoring Systems (AMS) in Germany is administered by TUV and UBA (the Federal Environment Agency). TUV and UBA are recognized internationally due to their extensive certification process and experience. TUV/UBA adopted the European standard EN 15267 Part 3 and incorporated the German domestic requirements (BlmSchV 17: suitable for incineration plant, BlmSchV 13: suitable for large combustion plant, and BlmSchV 27 and 30: suitable for other types of plants) in developing the QAL1 standard.
|European Union||RoHS (2011/65/EC)
The Restriction of Hazardous Substances Directive became effective in 2006. It restricts the use of six hazardous materials in the manufacture of various types of electronic and electrical equipment, and sets collection, recycling and recovery targets for electrical goods. It is linked to the WEEE directive.
The Safety Integrity Level (SIL) is a relative level of risk‐reduction provided by a safety function or to specify a target level of risk reduction. The International Electrotechnical Commission's (IEC) standard IEC EN 61508 defines SIL requirements according to hardware safety integrity and systematic safety integrity. A device or system must meet the requirements for both categories to achieve a given SIL.
The B-Series Mass Flow Meter has been approved for use in SIL1 Safety Instrumented Systems in Nuclear Facilities in the UK. An assessment was conducted by Sellafield Ltd in conjunction with British Energy and SP Laboratories using EMPHASIS. EMPHASIS is a tool adopted by the UK Nuclear Industry for assessment of smart instruments for use in nuclear applications. EMPHASIS is based upon a lifecycle approach as specified in IEC61508, and provides a rigorous evidence gathering tool covering all relevant aspects relating to the company and the product under review.
|European Union||WEEE (2002/96/EC)
The Waste Electrical and Electronic Equipment Directive was introduced in 1970 to improve the environmental performance of businesses that manufacture, supply, use, recycle, and recover electrical and electronic equipment.
PESO Zone 1
Certificate of Approval for Flame Proof Type Mass Flow Meters Ex d IIB+H2 Zone 1 use by the Government of India’s Ministry of Commerce & Industry Petroleum & Explosives Safety Organization (PESO)
PESO Zone 2
Certificate of Approval for Increased Safety Type Mass Flow Meters Zone 2 of Gas IIC use by the Government of India’s Ministry of Commerce & Industry Petroleum & Explosives Safety Organization (PESO)